view cart menu separator categories menu separator faq
advanced search
categories  > Amplifiers > Full Range- DSP Line- 1 Channel (4)
Taramp's DSP-1600 1ohm
 

Taramp's DSP-1600 1ohm

Price: $349.00 add to cart     
Feedback: 0%, 15 sales Ask seller a question
Shipping: US-Mainland: free (more destinations)
Sales Tax: Kentucky: 6%
Condition: Brand new
Payment Options: Money Order,
Authorized Distributor and Tech Advisor for Taramp's - SPL-Lab USA

Amplifier specifications-

Number of Channels - 1
@ 13.8 VDC - 1 OHMS: 1976W RMS
@ 13.8 VDC - 2 OHMS: 1304W RMS
@ 13.8 VDC - 4 OHMS: 751W RMS
@ 12.6 VDC - 1 OHMS: 1600W RMS
@ 12.6 VDC - 2 OHMS: 1066W RMS
@ 12.6 VDC - 4 OHMS: 620W RMS
Input and DSP:
Analog Digital Converter (ADC): 24-bit, 96kHz, 110dB Dynamic Range
Digital Signal Processor (DSP) 24-bit, 96kHz
Input Sensitivity for Maximum Output: 250mV (Vol = 100%)
Frequency Response @ -1dB: 22Hz to 20kHz (-1dB)
Frequency response @ -3dB: 18Hz to 30kHz (-3dB)
Total Harmonic Distortion (THD): 0.11%
Signal / Noise Ratio: >87dB

Full Digital Controlled settings
Crossover:
H. P. F (High Pass Filter): 20Hz to 1KHz (-24db) Variable (or Full Pass)
L. P. F (Low Pass Filter): 50Hz to Full Range (-12db) Variable
Bass Boost: 0 - 10.5 dB Centered at 50Hz
Input Impedance: 18k OHMS
Thermal Management: Smart Cooler (cooler driven by temperature or audio, with two speeds)
Protection: Short on the Output / Supply Voltage High/Low / Thermal
Minimum Supply Voltage: 9.0VDC
Supply Voltage: 16VDC Maximum
Consumption at Rest: 1.00 Amp.
Maximum Consumption Musical @ 12.6VDC: 87 Amps
Maximum Consumption in Sinusoidal Signal (1kHz) @ 12.6VDC: 174 Amps.
Dimensions (WxHxD): 9.06" X 2.87" X 6.97"
Weight: 4.4 lbs

Advanced Options
This amplifier has an onboard advanced configuration for even MORE features-

ANTI-Clipping Module- Variable from 1%-30%, this setting has the ability to resist speakers from being clipped or clipped for long enough to cause thermal damage.

Phase Control- 2 options to choose- 0 or 180.

Bass Boost Center Frequency Control- Change the centered frequency of boost from the following options- 40Hz, 50Hz (default), 60Hz or 80Hz

Recommendations of Operational Use-
SPL-Lab USA strongly advises to follow these guidelines to have error-free operation.

Do not mount amplifier to speaker box. Cyclic Vibrational Failure is #1 fail rate of amplifiers and these are lighter than most so their potential is higher if not followed.
Do not wire this amplifier lower than 1ohm nominal Impedance. (Equivalent to ~0.7 ohms DCR or Resistive measurement via DMM).
Do not clip amplifier above 14.5v for extended periods of time
Do not drive amplifier into clipping + protection for extended periods of time (exceeding 20% THD)
Other Products from spllabusa:View all products
AJK Sound Clip Extender
$49.00
Alphard Sound Deaf Bonce DB-183 1200wrms
$549.00
Alphard Sound Deaf Bonce DB-OGO-1500.2D 3000w
$699.00
Alphard Sound Machete M54 360w 4 Channel
$149.00
Taramp's VTR-1000 12v Voltmeter
$39.00
Taramps HD-5000 1ohm
$739.00
SPL-Lab Next-USB 4 Sensor Kit SPL dB RTA AC Power Measuring system
$984.00
SPL-Lab Next-USB 3 Sensor Kit SPL dB RTA AC Power Measuring system
$799.00
Taramps HD-3000 2ohm
$478.00
Alphard Sound Machete MFC650.1D 650w
$239.00
Last Updated: 26 May 2017 11:44:28 PDT home  |  about  |  terms  |  contact
Powered by eCRATER - a free online store builder